System Settings

Start

Manual Instructions

This manual includes symbology settings, function settings (lighting, keyboard type and factory reset, etc.) and interface settings. If you need to change the functions you need, just scan the configuration according to the setting barcode below. All with (*) indicate factory default values.

Version Information

In order for the host to quickly read the version information of the current device, you can confirm it by reading the “version information”.

Version Information

Set Code Switch

By turning on the setting barcode function, you can configure the parameters of the scan engine by scanning the setting barcode.

Note

When modifying the configuration through the setting barcode, the entire current flag bit list will be saved to the memory, that is, the configuration configured through the serial port but not saved will also be saved together.

Disable

* Enable

Set Code Content Output

Whether to output the setting barcode content, you can configure the parameters of the scan engine by scanning the following setting barcode.

* Disable

Enable

User Default Settings

Save Current Configuration As User Default

Restore User Factory Default Settings

Users can save their frequently used configurations as user default settings. By scanning “Save current settings as user default settings”, the current configuration information of the device can be saved as user default settings information. After this operation, the new configuration information will replace the original user default settings information. By scanning “Restore User Default Settings”, the scan engine can be switched to user default settings.

Power Control

Sleep Mode

This parameter determines the power mode of the module. In sleep mode, the code reading module enters sleep state as much as possible (can be awakened by wake-up command)

* Sleep Mode

Continuous Working Mode

In continuous working mode, the scan engine is still awake after each decoding attempt.

Continuous Working Mode

Lighting And Aiming

Illumination

The lighting can provide auxiliary lighting for shooting and reading, and the beam shines on the reading target, improving the reading performance and the ability to adapt to weak ambient light. Users can set it to one of the following states according to the application environment:

Normal lighting (default setting): The lighting lights up when shooting and reading, and turns off at other times;

The lighting is always on: the lighting will continue to glow after the scan engine is turned on;

No lighting: The light does not come on under any circumstances.

*Normal Lighting	No Lighting
Lighting Always On

AIM

The projected aiming beam helps users find the optimal reading distance when shooting for reading. According to the application environment, users can

Choose any of the modes below.

Aiming Normal (default setting): The scan engine only projects the aiming beam when shooting and reading;

Aiming always on: After the scan engine is powered on, it will continue to project the aiming beam;

No Aiming: The aiming beam is extinguished under any circumstances.

* AIM For Normal	No Aiming
AIM For Constant Light

Prompt Output

Prompt Sound Related

Beeper Type

Read the following setting barcode to set the buzzer as a passive or active buzzer.

* Passive

Active

Volume Level

Users can adjust the buzzer volume according to the application environment and personal habits by reading the following setting barcode.

mute	Bass
Alto	* Treble

Power-on Beep

Disable

* Enable

Setup Code Prompt Tone

Disable

* Enable

Decoding Tone

Disable

* Enable

Decoding Prompt Tone Frequency

The resonant frequency of the buzzer used by the user may be different from the default frequency. You can adjust the frequency of the decoding prompt tone by reading the following setting barcode. Default is 2700Hz.

Scan the “Buzzer Frequency” setting barcode

Buzzer Frequency

Scan the “Digital Setup Code”. For example, if the frequency is 1500Hz, sweep 1, 5, 0, 0; if the frequency is 2700Hz, sweep 2, 7, 0, 0

Scan the “OK” setting barcode to end the setting

Sure

Decoding Prompt Sound Quick Setting

1000Hz	1500Hz
2000Hz	2500Hz
*2700Hz	3000Hz
3500Hz

Decoding Tone Duration

Users can set the duration of the decoding prompt sound as needed, the default is 50ms.

Scan the “Beep Sound Duration” setting barcode

Prompt Tone Duration

Scan the “Digital Setup Code”. For example, if the duration is 50ms, scan 5,0; if the duration is 200ms, scan 2,0,0

Scan the “OK” setting barcode to end the setting

Sure

Quickly Set The Decoding Tone Duration

30ms	*50ms
70ms	100ms
200ms	300ms

Reminder Light Related

Alert Light Function Type

* Decoding Hints

Power Prompt

Decode Success Indicator

Disable

* Enable

Decoding Success Prompt Light Control Method

Mode 0: long off after power on, on when decoding is successful, on for a specified time and then off.

Method 1: Always on when power is on, off when decoding is successful, and on after a specified period of time.

* Mode 0

Way 1

Decoding Status NR Output

NR is the abbreviation of No Read. Before releasing the trigger button, if the barcode cannot be decoded within the timeout period, the “NR” message is allowed to be output; when this function is disabled, no message can be output to the host even if the barcode cannot be decoded.

* Disable

Enable